scotts spreader settings lbs per 1000 sq ft

For application using a pushed broadcast spreader, Scotts recommends a setting of 5 1/2 when overseeding and a bare-lawn setting of 8 1/4. With a handheld broadcast spreader, Scotts recommends a setting of 4 when overseeding or seeding a new lawn but suggests that the sower make two perpendicular passes for new areas.

What number do you set Scotts fertilizer spreader?

After choosing the best broadcast spreader for your yard, locate the orange dial on the spreader and turn it to the setting indicated on the seed or fertilizer bag. Turn clockwise for a higher setting of 12 or 14, which is for larger granules or grass seed, or counterclockwise to reach a lower setting of three or five.

What do numbers mean on Scotts spreader?

For fertilizer spreaders the numbers usually represent the amount of fertilizer that is to be applied over a specific square feet of land. On spreaders you can find numbers such as 5, 5 and a half or 18 and a half.

How do you determine spreader settings?

Calibrating Your Spreader
Divide 100 by the square foot the bag of fertilizer covers.Multiply the weight of the bag by this number.The answer is the amount of fertilizer needed to cover 100 sq. ft.Place this amount in the spreader.Mark off a 10 ft. x 10 ft. area.Apply using the suggested setting.

What setting should my lawn spreader be on?

Place your spreader setting on a low setting (usually one-fourth of the spreader setting range or less). Spread the material over a 50 x 20-foot area (1,000 square feet). If there is material left over, increase your setting. If you come up short, decrease your setting.

What setting should I use for grass seed spreader?

Agway recommends a setting of 15 for overseeding and 18 for a new lawn when using either their rotary spreader or an Earthway rotary spreader. With an Agway drop spreader, use a setting of 18 for overseeding and 22 for new seeding.

How do you spread Scotts fertilizer?

Here’s how to do it.
Water your lawn. A few days before you feed your lawn, give it a good watering. Pick the best spreader for your lawn. Spreaders fall into two main categories: broadcast and drop. Apply grass fertilizer around the perimeter. Fill in the middle. Properly handle remaining product.

How do you prevent stripes from fertilizer?

More specifically, the stripes are caused by not aligning the spreader as you make each pass. Most spreaders, either drop or broadcast, will have an “edge” where the fertilizer hits the lawn. These “edges” need to be aligned so that there is little overlap or gap between them.

How do I use Scotts EdgeGuard mini?

Fill hopper with Scotts® lawn fertilizer or grass seed. Turn orange rate dial to the desired “Broadcast/Rotary Spreader” setting listed on the back of each Scotts® product. To apply product begin walking, then squeeze and hold trigger. NOTE: Each pass should be within 1.5 metres (5 ft.)

What setting do I use for Step 1 spreader?

Spreader Settings
Scotts® Broadcast / Rotary Spreader – (Turf Builder® Edgeguard Mini, Basic, Standard, Deluxe Edgeguard, Edgeguard DLX, Lawn Pro & Speedy Green) – Set to 3.Scotts® Drop Spreaders – (AccuGreen, Classic Drop) – Set to 6.Scotts® Easygreen® – Set to 27 1/2.Scotts® Wizz™ – Set to 3 3/4.

Do you need a spreader for fertilizer?

Do You Need a Spreader? If you’re going to spread fertilizer on your lawn then you really shouldn’t do it without a spreader. There are two types of spreaders: broadcast and drop. Drop spreaders are for more targeted applications, while broadcast spreaders are good for covering a large area quickly.

When should I apply 10 10 10 fertilizer to my lawn?

Fertilize warm-season grass twice in the spring and twice in the fall. Apply the first spring application when new growth begins and the second application 30 days later. Apply the first fall application after the grass’s fast summer growth slows and the second application 30 days later.

Which is better drop or broadcast spreader?

A broadcast spreader will take extra care to make sure different parts of the lawn receive an even coverage. A drop spreader, as previously mentioned, is more precise because it doesn’t broadcast the granular product or seed and doesn’t change the amount spread based on a changing walking pace.

How do you overseed?

“Overseeding” the term for adding more grass seed to a lawn without turning the topsoil. For many homeowners, overseeding is part of general lawn maintenance.

STEP 1: Mow and rake the lawn. STEP 2: Amend the soil. STEP 3: Spread the grass seed. STEP 4: Add grass seed fertilizer. STEP 5: Water the seeded lawn.